Core industries blanks

Discuss shaping and repairing techniques here.

Moderators: Butts, Shari, collnarra

Post Reply
diggerdickson
barnacle
Posts: 2316
Joined: Sat Jan 10, 2009 11:26 am
Location: home is where the heart is.

Core industries blanks

Post by diggerdickson » Sat Sep 01, 2018 6:20 pm

Doea anyone use these blanks. Any experience with these is appreciated
no, Im not a surfer, Im just a garbage man".

User avatar
saltman
Owl status
Posts: 4123
Joined: Tue Dec 13, 2005 4:52 pm
Location: a short walk up the beach

Re: Core industries blanks

Post by saltman » Sat Sep 01, 2018 6:48 pm

They are made locally and ared used by plenty of local shapers with no complaints
I am not sure they are quite up to surfblanks or burford quality
As I Recall Huie wasn’t a fan
smnmntll wrote:
Thu Nov 15, 2018 11:20 am
Look, OK, cards on the table. I fcuked my father up the arse. It was in the car immediately following my mother's funeral and on the way to the wake.

diggerdickson
barnacle
Posts: 2316
Joined: Sat Jan 10, 2009 11:26 am
Location: home is where the heart is.

Re: Core industries blanks

Post by diggerdickson » Sat Sep 01, 2018 8:31 pm

There’s a mob in Hobart who are suppliers for them. It’s only a 5 hour drive there to get some blanks, resin and glass. I might not have any other options :(
no, Im not a surfer, Im just a garbage man".

diggerdickson
barnacle
Posts: 2316
Joined: Sat Jan 10, 2009 11:26 am
Location: home is where the heart is.

Re: Core industries blanks

Post by diggerdickson » Sat Sep 01, 2018 8:35 pm

The only other way is to get some sent over, not a option really
no, Im not a surfer, Im just a garbage man".

cedric
Grommet
Posts: 58
Joined: Fri Dec 27, 2013 10:45 am

Re: Core industries blanks

Post by cedric » Sun Sep 16, 2018 10:55 am

They do a nice Marble look / resin swirl blank.

User avatar
saltman
Owl status
Posts: 4123
Joined: Tue Dec 13, 2005 4:52 pm
Location: a short walk up the beach

Re: Core industries blanks

Post by saltman » Sun Sep 16, 2018 6:41 pm

I have only used burford
A recent board had quite a few air bubbles Apparently it’s more common now as manufacturers attempt to make the blanks whiter - little gas pockets are a side effect
smnmntll wrote:
Thu Nov 15, 2018 11:20 am
Look, OK, cards on the table. I fcuked my father up the arse. It was in the car immediately following my mother's funeral and on the way to the wake.

buddy
barnacle
Posts: 1626
Joined: Thu Mar 10, 2016 6:34 pm

Re: Core industries blanks

Post by buddy » Sun Sep 16, 2018 6:53 pm

I don't even like them super white.
I don't mind the off white.

cedric
Grommet
Posts: 58
Joined: Fri Dec 27, 2013 10:45 am

Re: Core industries blanks

Post by cedric » Sun Sep 16, 2018 7:22 pm

They do a range of colours as well.

User avatar
jimmy
Harry the Hat
Posts: 2793
Joined: Fri Jun 05, 2009 12:12 pm

Re: Core industries blanks

Post by jimmy » Sun Sep 16, 2018 9:05 pm

I had a blank piece of paper once. And then I wrote on it. And then I had a cup of tea. #beanpoling #isthatwhatyoumeant

User avatar
saltman
Owl status
Posts: 4123
Joined: Tue Dec 13, 2005 4:52 pm
Location: a short walk up the beach

Re: Core industries blanks

Post by saltman » Mon Sep 17, 2018 7:06 am

That is some core beanpoling
smnmntll wrote:
Thu Nov 15, 2018 11:20 am
Look, OK, cards on the table. I fcuked my father up the arse. It was in the car immediately following my mother's funeral and on the way to the wake.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests